by admin June 6, 2023 0 Comment 21 min read
Is the volume button on the Dish remote not working? You don’t have to worry because it can be fixed easily. It is caused by signal obstructions, discharged batteries, pairing issues, stuck buttons, etc. Instead of buying a new Dish remote, we recommend users try these workarounds to fix the volume not working issue. If the Dish remote has become malfunctioned due to defective hardware, you can buy a universal remote as a replacement.
Table of Contents
Why is Dish Remote Volume Not Working
These are the reasons that would be responsible for the Dish remote volume not working.
| SCENARIO | REASONS |
|---|---|
| 1 | If the Dish remote is running out of charge due to drainedbatteries |
| 2 | If there is anydebrisstuck on the volume button of the Dish remote |
| 3 | The volume key may be broken because of accidentalphysical damage. |
| 4 | There is a technical issue with the Dish receiver for receiving signals |
| 5 | Due to obstructions, the IR remote won’t send signals to the receiver |
| 6 | The remote may have pairing problems with your TV or receiver |
| 7 | When the Dish remote has not been set to control the TV volume |
How to Fix Dish Remote Volume Not Working
The following workarounds would help you fix the volume button not working issue in the Dish remote.
Check the Batteries
Before getting into the advanced steps, first, check your remote batteries. If the batteries on your remote areexpiredor running out of charge,the remote may stop working at any time. So you have to replace the old batteries with newer ones whenever required. Eject the old batteries from the Dish remote compartment and insert the new batteries based on their positive and negative polarities.
Note: If Spectrum TV remote stops working, it may be due to discharged batteries. Like the Dish remote, replacing the batteries will make it work normally.
Power Cycle Dish Remote
Another easiest way to fix the volume button not working in the Dish remote is to power reset. It will eliminate the unused residual power and help the remote to work.
[1] Pop out the batteries from the Dish remote’s battery compartment.
[2] Now, press and hold each button on the remote for 2 seconds.
[3] Keep pressing the Power button for about 30 seconds.
[4] Now, insert the batteries back into the remote.
Later, program the Dish remote to the TV or receiver and test if the volume control is working fine.
Change Default Audio Output Device
Sometimes, the remote volume won’t work when an improper audio output is selected. Hence, you need to choose the audio output that you want to control with the Dish remote.
[1] Go to Settings and select the Audio or Audio Settings tab.
[2] From there, choose the Default Output Device option.
[3] Under the drop-down menu, select Default.
Now, press the volume button and see if it works or not. If not move to the following method.
Enable Dish Remote to Volume Control
If the Dish remote changes channels but not volume, it is because of some wrong configurations. By enabling volume control on Dish settings, you can get rid of this issue.
[1] Press the Home or Menu key on the Dish remote.
[2] Go to Settings > Remote Control > Customizations.
[3] Check whether the Volume & Mute keys are enabled to control the TV volume.
[4] If not, enable these functions to control the TV volume.
Later, operate the Dish remote and check the volume and mute functions are working or not.
Disable Third-Party Devices
In rare cases, the external third-party devices connected to the TV may cause interference with the Dish remote volume. It is recommended to unplug the unused external devices connected via Coax, HDMI, or RCA. After unplugging them, check if the Dish Volume button is working fine or not.
Reprogram the Dish Remote
If the Dish remote volume is not working after changing batteries, it means that it is not programmed properly. So, you can reprogram the Dish Remote to the receiver or the TV.
[1] Navigate to the Dish Network Menu.
[2] Select the Remote Control option and choose the desired device that you want to pair.
[3] Then, choose your Next and wait for a few seconds for the remote to get programmed with the receiver.
Steps to Program Dish Remote to TV Without Receiver
[1] Turn on your TV and press the TV button on the Dish remote.
[2] Press the # (pound) button. Following that, press the red power button.
[3] Keep pressing the UP button every second and wait for the TV to turn off.
[4] Once switched off, turn on the TV and use the remote to see if the issue got fixed.
Note: If the volume button on Dish 54.0 remote control is not working, you can try re-pairing the remote.
Re-pair the Remote to Receiver
If the Dish remote fails to control the volume on the receiver, it means that it has been unpaired. To fix this issue, you can re-pair the remote to the receiver to make it work.
[1] Press the System Info button on the receiver.
[2] Press the Sat button on the front or side of the Dish remote.
[3] Further, press the Cancel or Back button on the remote.
You have successfully paired the Dish remote with the receiver.
Reset Your Smart TV
[1] Turn on your TV and navigate to the Settings menu.
[2] From the Settings menu, select the System tab.
[3] Choose Reset and select Factory Reset Everything.
[4] Click on Confirm to complete the reset process.
Note: You can reset your LG Smart TV if you have issues pairing the Dish remote to an LG TV.
Factory Reset Dish Receiver
[1] On your Dish remote, press the Home button.
[2] Go to the My Dish TV page and select the Tools Configuration tab.
[3] Scroll down and select Factory Reset.
[4] Press the Ok button on the remote.
[5] Choose the Reset option and follow the on-screen prompts to complete the resetting process.
Factory Reset Dish Remote
If the above methods do not work, you should reset the Dish remote to its factory settings. You need to remember that, when you reset the remote, the data or configuration in your receiver system will get erased.
[1] On the Dish Remote, locate the SAT button and press it.
[2] Go to the Receiver and press the System Info option.
[3] To confirm the reset, press the SAT button again.
If the Dish remote is no longer working after resetting, it is better to buy a replacement remote.
Contact Dish Support
If none of the workarounds fix the Dish remote not working issue, you can reach out to Dish customer support. You can talk to a customer service executive by dialing 1-800-333-3474 from your registered mobile number. By visiting the support webpage, you will also get instructions related to programming the remote to the TV or receiver.
Buy a Universal Remote
If you have lost the Dish remote control or it hasphysical damage,then you can replace it with a new remote controller. You can buy the original remotes onAmazon which contains all Dish remote models. Make sure to double-check the remote description carefully as it may be compatible with the particular receiver.
FAQ
1. Why is the volume button on my remote not working?
The primary reason is poor or dead remote batteries. So, replace the batteries with new ones. If still, the Volume button does not work, follow the troubleshooting fixes listed in this article.
2. Can I use the DISH Anywhere app as a remote?
No, you cannot use the DISH Anywhere app as a remote. Instead, you can use third-party universal remote apps to control your Dish receiver from a smartphone.
